Just How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Just How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
What're your ideas with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably tough job. If the old bathtub is readily available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. See to it you have actually qualified yourself for the task and also fit attempting it. Instead of working with a service provider to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube links.
This write-up will aid you mount a new tub in your washroom if you have actually already gotten a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools and also product checklist ought to make up the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and examine all joints and also new pipework for leaks as well as tighten them if required. Load the tub as well as additionally check the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making certain that the washing machines are in area between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in complications with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our part about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking the time to read our article post. Are you aware of another individual who is interested in the subject? Please feel free to promote it. We recognize the value of reading our article about Installing A Bathtub.
Get Your Estimate Now
Report this page